Esh's Aurunmilla - Owners Manual - Not available
Esh's Aurunmilla - Schematics - Not available
Esh's Aurunmilla - Audio Cable Pinout
Esh's Aurunmilla - Game Settings (On Screen Programming)
Behind the coin door, keep the test button pressed while turning on the game to enter test mode.
Select the various options by using the joystick and action button.

Esh's Aurunmilla - ROM Images
Esh's Aurunmilla - ROM Images (Alternate 1)
Esh's Aurunmilla - ROM Images (Alternate 2)
Esh's Aurunmilla - ROM Images (Level 7 Game Over Bug Fix - made in 2017)

Esh's Aurunmilla Virtual Library - Images and information of the major components

 

 

Compatible Laserdisc Players - Pioneer LD-V1000

Pioneer LD-V1000 - Operating Instructions (7 pages)
Pioneer LD-V1000 - Interface Guide (24 pages)
Pioneer LD-V1000 - Service Manual (81 pages)
Pioneer LD-V1000 - Schematics (27 pages)
Pioneer LD-V1000 - Cleaning the Optics (1 page)
Pioneer LD-V1000 - Changing the Laser Tube (3 pages)

Conversion Cards - The original Pioneer LD-V1000 laserdisc player is not natively compatible with any other model, making direct substitution impossible.  Various products have been developed over the years to allow replacement/upgrade of the laserdisc player.

Dexter is the newest product.  Unlike the other products below which convert to a newer laserdisc player model, no player or disc is needed with Dexter.  The Dexter board is a drop-in replacement which poses as a laserdisc player and plays the video for the game digitally, from a custom file format without video compression.  Dexter accepts the original commands from the PCB through the original interface cable.  Dexter has been going in and out of production multiple times, per demand, via pre-order process only.

LaserCon is a laserdisc player conversion card that allows the game to use newer supported Pioneer players.  LaserCon is no longer in production.

The LaserAce conversion card allows the game to use a variety of different Pioneer and Sony laserdisc players.  LaserAce is no longer in production.

 

 

Interchangeability - Interstellar Laser Fantasy can easily be converted to Esh's Aurunmilla by following the steps outlined below by Matteo Marioni and Brendon Zeidler.

Remove the Interstellar main PCB (set of three boards) and the laserdisc from the Interstellar cabinet.  Esh's Aurunmilla uses the Sound PCB, the Super Impose PCB, and all the same wiring in an original Interstellar cabinet.  Be careful when hooking up the Esh's PCB to the wiring.  Interstellar uses two black harness connectors, but only one is used by the Esh's PCB.  Use the black harness connector that carries most of the wiring (it's a little bigger than the other connector), and it should be inserted with the red wire (+ 5V) on the right side.  Pin 1 of the Esh's connector is GND and pins 3 & 4 are +5V, so be careful before hooking it up.  If you are not sure which wire is +5V on the Interstellar wiring harness, a DC voltage meter may help.  The 6-pin connector on the Esh's PCB on the right, labeled "CN 1", is the "PCB generated audio output".  It goes into the "CPU IN" audio connector on the Interstellar sound board.  Finally, connect the Esh's PCB to the LD-V1000 and install the Esh's disc.

LD-V1000 Boot Switch - A simple inexpensive way to build a switch that issues a play command to the LD-V1000 or LD-V1001.  Check it out here.

Manufacturer:
Funai / Gakken
(Japan, 1984)

Emulation and Ports
Virtual Library
Game Info

Message Board
Classifieds

Collectors
Chat Room

 

QUESTIONS? COMMENTS? PROBLEMS?
Contact Us

HOME | LASER GAMES | LASER COMMUNITY | TECH CENTER

This website was created by Jeff Kinder & Dave Hallock, 1997 - 2018.
All trademarks and copyrighted materials are property of their respective owners.